Plans For The Advanced
Homemade ( Slimguy) Penis Extender:
free plan for the advanced homemade penis extender is very good
but does require some skill with tools. It was designed by a guy
with the internet handle "Slimguy" and is a rough copy
of professional extender devices.
Warning: We have nothing to do with this design.
It is another guy's invention. We only present it here for your
information. We cannot offer any additional help or advice about
the Slimguy homemade extender.
Homemade Penis Extender Plans:
This traction device was built out
of about $12 US in parts. Similar devices retail for hundred of
dollars. Note the small springs near the base.
The "Home Hardware Extender," before
assembly, with screwdriver, two drill bits and surgical gauze (not
shown). Note the various holes drilled into the cut, filed, and
sanded PVC parts.
1Latex tubing 1/4" O.D., 1' $1.00+ (per foot) (available at Medical
Supply and/or Aquarium Supply stores)
- Schedule 40 Flush Bushing PVC (1)
2" x 1-1/2" $1.10
- Schedule 40 PVC Coupling (1) 2"
- Turnbuckles (2) 5/32", 4-3/4" Eye/Eye
- Gate Hook & Eye (2) 2 1/2" $0.70
- Wing Nuts (2) $0.70 package
- Metal Washers (4) $0.25 total Machine
Screws (4) 5/32" x 3/4" $0.70 package
- Metal Nuts (2) 5/32" $0.70 package
- Metal Springs (2) 1/4" x 1/2"-3/4"
x .020" (0.5mm) $1.25 package
- Rolled Gauze, Sterile, 2" width
- Large Metal Paper Binder Clip $0.50
- l Wood Saw
- l Metal Saw
- l Drill and Bits (1/4", 5/32")
- l Screwdriver
- l Vise
- l Sandpaper (60 - 150 grades)
- l Pliers
- l File
- l Scissors
CONSTRUCTING the HOME HARDWARE EXTENDER
Drill two 5/32" holes into the PVC
Flush Bushing, opposed from each other, and about 3/4" from the
bottom (where the lip extends). If desired, saw off about 3/8" from
the top of the PVC Flush Bushing so that there will be more room
through which the penis may be pulled and maneuvered. If the PVC
Flush Bushing is not round along the inner rim, you should file
and sand it so for safety and comfort. The bottom of the base may
be lined with foam rubber strips for a greater comfort. Additionally,
you may file and sand the PVC Flush Bushing in such a manner as
to make a more ergonomic fit.
With a pair of pliers, carefully remove
each of the wood screws from each of the pair of Gate Hooks. Saw
off the curved ends of the Gate Hooks and file the ends smooth.
Upon each of the 5/32" diameter, 1/2"
long Machine Screws, thread a washer, an eye-end of each of the
two Gate Hooks, and another washer or two. Carefully screw each
assembly through the opposing holes of PVC Flush Bushing. Preferably,
no metal should protrude through the either side of the bushing.
Each Screw-Turnbuckle assembly should be firmly in place, with the
turnbuckles perpendicular to the PVC Flush Bushing.
Saw the 2" PVC Coupling latitudinally
so that the length measures about 1 3/4"; then saw it longitudinally
so that a "half pipe" results. Drill 2 5/32" holes into the half
pipe on opposite sides, each about 1/2" from the rounded base, and
3/8 from the sides.
Drill two 1/4" holes about 3/8" apart
(measured between radii) and 1/2" from the top of the half- pipe.
Through these holes will the rubber or latex tubing be threaded.
Sand the half pipe round and smooth. You may saw the top corners
of half pipe for a more ergonomic design (as in Figure 1), but be
careful not to compromise structural integrity.
Thread a Wing Nut and a large metal
washer onto each of the 2 3/4" Machine Screws and then drive the
resulting 2 assemblies into each of the 5/32" holes in the half
Place a small metal washer and a small
spring onto each of the perpendicular Gate Hooks, and then drop
each of the Turnbuckles (sans eye hook). The fit should be smooth.
If not add or subtract washers from the Gate Hook assemblies.
Thread the Latex Tubing through the
1/4" holes in the half pipe. Due to the tightness, you may need
to pinch the tip of the Tubing. The Tubing should be held firmly
by the holes, but you may use a large metal paper binder clip for
MEASURING THE TENSION
Thread the two 1/4" holes in the Home
Hardware Extender with string and then thread the tail of the remaining
string through the Flush Bushing assembly. Tie the string to carefully
measured weights of 0.6 kg (1.3 lbs.), 0.9 kg (2.0 lbs.), 1.2 kg
(2.6 lbs.), or 1.5 kg (3.3 lbs.). Plastic water bottles make good
weights (1 pint = 1 pound, 500 ml = 0.5 kg, etc.). Hold the Home
Hardware Extender with one hand, and with the other, a ruler to
measure the depression of the springs. Carefully measure and note
the length of the springs for each of the remaining weights.
For example, the 2 springs on the example
in Fig. 1 (each 5/8" long, and 0.020" gauge) depress to a length
of about 1/2" with 1.3 lbs. (0.6kg), 3/8" with 2.2 lbs. (1.0kg),
and 1/4" with 3.3 pounds (1.5 kg). You may mark in ink or crayon
the results for each weight on the gate hook.
Over time, you may need to extend the
device, and therefore the penis, by twisting the turnbuckles further
in order to obtain the same tension. This is due to extension and/or
growth of the penis.
USING THE HOME HARDWARE EXTENDER
With the device in two parts (Bushing/Turnbuckle
and Half-Pipe/Tubing), pull the penis through the PVC Bushing, with
the Turnbuckles at their minimum length. Then loop the penis head
through the tubing and tighten by pulling from the other side. Carefully,
pull the Half-Pipe/Tubing assembly until the Turnbuckle hooks can
be attached and screwed tight to the Machine Screws in the Half-
Pipe. This procedure takes about 1-3 minutes. Tension is increased
or decreased by twisting the turnbuckles. You may use a large metal
paper binder clip to hold the rubber tubing protruding from the
back side of the Half-Pipe in place.
It is recommended that you wrap the
glans and coronal groove of the penis in about 20 cm (8") of sterile
Surgical Gauze for comfort, to reduce the chance of pinching where
PVC and Tubing meet, to avoid sticking of tubing to sensitive skin
after long stretch sessions, and for hygiene.
During the first 2-3 weeks of your
traction regimen, initial tension should be no less than 0.6 kg
(1.3 lb.) and no more than 0.9 kg (2.0 lbs.); time in traction should
start at 4 to 6 hours per day. After the regimen of the first 2-3
weeks, increase the tension to between 0.9 kg and 1.2 kg; daily
use should increase to 8-12 hours. You should wear the device for
10-12 hours per day for 3-6 months to gain acceptable results.
Check the color and temperature and
feeling of the glans periodically. If it turns blue or cold or numb
remove the device immediately, wait 10 minutes and reattach, making
sure that the fit is not as snug, or the extension not as severe.
If the noose is attached correctly, erections should not pose any
problem, since as the penis grows, the pull will lessen, and the
Latex tubing will expand when the head swells. Sometimes the penis
will slip out of the Extender, but given correct placement of the
Gauze this should not pose a danger.
As with other "Extenders," if traction
is more than about 1.0 kg (2.2 lbs.) of pull or more, the device
should be worn continuously for no more than about 2 hours, with
10-15 minute breaks between sessions. Trimming the pubic hair to
prevent snagging in the base-plate assembly is also recommended.
For many users, including the author, 1 to 1.5 hour sessions are
more comfortable, if less convenient.
If wearing the device for over 2 hours
(or overnight), exercise EXTREME CAUTION. Do not use more than 0.6
kg (1.3 lb.) of pull, and adjust the Surgical Tubing so it is as
loose as possible without the glans slipping out. Gently exercise
the penis immediately after use. Involuntary detachment while sleeping
may occur, but this should not be dangerous.
Hot compresses (towels soaked in hot
water and wrung dry) may alleviate some of the discomfort encountered
while wearing an Extender-Type Device, as might directly inserting
the penis into warm water. This can be done before, during, after,
or between traction sessions. Such "heat therapy treatment" will
not only feel pleasant, it will also increase the flow of blood
to ligaments, nerves, tendons, and the small amount of muscle tissue
in the penis. Some studies have even suggested that heat can increase
the rate of tissue distraction.
Copyright penisstretchingtechniques.com All rights reserved.